The easiest way to repair an oil filter housing that is leaking after an oil change is to remove the housing and replace the gasket. First, make sure that the engine is cool and then jack up the car. Place a jack stand under the frame and remove the wheel. Next, locate the oil filter housing and use a wrench to loosen the bolts. Be careful not to drop any of the bolts into the engine. Once the bolts are loose, remove the housing and set it aside.
Hello, car enthusiasts!
If you’re like most people, you love your car. You take care of it, and you make sure that it runs great. But, like all things, your car needs some maintenance. And one of the most important and often neglected parts of your car is its oil filter housing.
Oil filter housing is a part of your car’s engine that helps to trap dirt, dust, and other particles that may be harmful to your engine. But, like all things, it can wear down over time. This can cause oil to leak from the housing, which can lead to a number of problems.
In this article, we’re going to explain how to repair oil filter housing leaking after oil change. We’ll also discuss the dangers of oil leaks, and how to prevent them from happening in the first place. So, let’s get started!
What is an Oil Filter Housing?
An oil filter housing is a part of your car’s engine that helps to trap dirt, dust, and other particles that may be harmful to your engine.
When you change your car’s oil, the technician will usually remove the old oil filter housing and install a new one. This is why it’s so important that the oil filter housing is leak-free!
If the oil filter housing is leaking, it will allow dirt, dust, and other particles to enter your engine. This can lead to a number of problems, including:
- Decreased engine performance
- Decreased fuel efficiency
- Increased emissions
How To Repair Oil Filter Housing Leaking After Oil Change?
If your oil filter housing is leaking, there are a few things that you can do to repair the damage.
1. Replace the Oil Filter Housing:
When you change your car’s oil, you should also replace the oil filter housing seal. If you don’t, the old seal will start to leak and cause major problems down the road. Here’s how to replace the oil filter housing seal:
- Drain the oil from the engine.
- Remove the old seal from the oil filter housing.
- Apply a thin coat of silicone sealant to the new seal.
- Insert the new seal into the housing and press it into place.
- Reattach the oil filter and tighten it down.
- Refill the engine with fresh oil.
2. Seal the Oil Filter Housing:
If you’ve ever changed your car’s oil, you’re probably familiar with the oil filter. Located on the bottom of the engine, the oil filter catches harmful particles from the engine oil before it circulates throughout the engine. Over time, these particles can build up and eventually cause damage. That’s why it’s important to replace your car’s oil filter at recommended intervals.
If you’ve just changed your car’s oil and are noticing a leak from the oil filter housing, don’t worry – it’s a common problem that can easily be fixed. Here’s how:
- Start by draining any remaining oil from the engine.
- Remove the old oil filter and dispose of it properly.
- Apply a thin coat of sealant to the gasket on the new oil filter.
- Screw in the new oil filter until it’s tight.
3. Replace the Engine Oil:
If you’ve recently changed your engine oil and now see oil leaking from the filter housing, don’t panic. It’s likely that you just didn’t tighten the filter housing enough after the oil change. Here’s how to fix it:
- Begin by tightening the filter housing as much as you can with your hands.
- If that doesn’t stop the leak, use a wrench to tighten it further. Be sure not to over-tighten it, or you could damage the seal and make the problem worse.
- If the leak persists, check for damage to the seal around the base of the filter housing. If you see any damage, replace the seal and try again.
- If everything looks okay and the leak still persists, your best bet is to replace the entire filter housing unit.
There are a few things that you can do to help prevent oil leaks from happening in the first place.
1. Keep Your Oil Filters Intact:
The first thing you can do is to keep your oil filters intact. If you don’t replace your oil filters when they’re due, it can cause oil leaks. It’s also important to make sure that the gasket is in good condition so that it doesn’t leak.
Another thing you can do is to check the seal on your engine. If the seal is worn out or cracked, it can cause oil leaks. You should also make sure that the bolts are tight and that there are no cracks in the engine block.
2. Check For Leaks:
One of the best ways to help prevent oil leaks from happening is to check for leaks regularly. You can do this by looking for signs of a leak, such as oil on the ground or puddles under your car. You can also check your engine oil level regularly to make sure that it’s not too low. If you do have a leak, be sure to fix it as soon as possible.
3. Check Your Brakes:
One of the most important things that you can do to help prevent oil leaks from happening in the first place is to check your brakes. Make sure that the brake pads are in good condition and that there is no debris or other obstructions on the brake discs. If you notice any problems with your brakes, be sure to have them fixed as soon as possible.
Another thing that you can do to help prevent oil leaks is to make sure that your car is properly tuned up. This includes making sure that all of the filters are clean and that the oil level is correct. If your car isn’t running optimally, it will be more prone to oil leaks.
Finally, be sure to keep an eye on your engine for any signs of trouble. If you notice any leaks, strange noises, or other problems, take your car in for a tune-up right away.
Conclusion: Oil Filter Housing Leaking After Oil Change?
If you are experiencing an oil leak after changing your oil, it is likely that the oil filter housing is the culprit. Fortunately, this problem is easy to fix and can be done in just a few minutes. All you need is a wrench and some sealant. Be sure to properly clean and seal the housing before reassembling the parts, and you should be good to go.